How To…. Carve an Aures Campfire Crane – Single Fork

one upright – two cranes – three pots

I could never call myself a chef however I could call myself a campfire engineer. I love to make different cooking rigs that I can use around the fire depending on the circumstances I find myself in.

The Aures crane is one of these projects for the more long-term camp and is so easy to make. The crane is named after Victor Aures, a Scout Master from Buffalo, NY. I found a good article on this from an issue of the Boy’s Life from 1915.

Photo 29-05-2015 09 33 30
The Aures Crane – a version using a single-fork branch

I also found a book called The Book of Camp-Lore by Dan Beard on the Project Gutenberg website that shows the original idea of wrapping the bark of one limb around an upright and a forked lower limb.

Aures crane
The Aures Crane – Picture courtesy of The Book of Camp-Lore and Woodcraft, by Dan Beard – Sourced from Project Gutenberg

I have been making these cranes for many years now but it was only once I started researching them that I discovered its correct name. This post does not cover the making of the Aures crane as shown in the Boy’s Life magazine or on in the Book of Camp-Lore (I will do that one later) but a variation of it.

The picture below shows a classic Aures crane with a good secondary fork to rest against the upright. It’s not easy to find the exact combination of forks needed for this classic style so I set out to re-create the Aures crane using a branch with only one fork, as these are so much more common.

Photo 29-05-2015 09 33 29 (1)
The ideal Aures Crane with a perfectly placed fork

I chose a sturdy green piece of hazel wood with a single fork. After trimming the ends to the size I wanted I used my axe to get rid of all the lumps and bumps on the wood.

In the bottom right picture the limb on the left I will be calling the upper limb and the one on the right the lower limb.

Photo 29-05-2015 09 33 18
The not-so-ideal single fork – much easier to find

Top Limb

Next I whipped some strong non-stretchy string onto the top limb of the crane. Grogs knots have a good tutorial on this, however it’s not necessary to whip in any particular way-  just do it in whatever way works for you and binds that end of the limb tightly.

Photo 29-05-2015 09 33 20
Whip the end of what will be the top limb

One of the reasons I selected a fairly sturdy fork was that I needed to put in a stop cut about a third of the way down the top limb. This stop cut will help you greatly in controlling the split you need to make to form the hook.

I sawed my stop cut to about two thirds of the diameter of the limb.

Photo 29-05-2015 09 33 20 (1)
Put a stop cut into the limb

Using small cuts I then cut out a groove just above the stop cut towards the fork to the depth of the stop cut (the two bottom left pictures). This allowed me enough space to get my knife blade in to start battoning down to split the wood.
I was very careful when battoning not to let the blade touch the string that I had whipped onto the limb. Take care to wiggle the knife to remove it, keeping your non-knife hand well clear. I battoned a number of splits so as to easily carve them out.

Photo 29-05-2015 09 33 21
Carve and batton

I also found that sawing down into the split helped with removing the wood. Once I had sawn or battoned down a number of times I carved out the excess wood by pressing down with my knife at a slight angle (you can just see the carved out area in the bottom left picture).

Next I took a small stick and carved it into a wedge shape to batton into the fork to expand it further.

Photo 29-05-2015 09 33 22 (1)
Use a saw and knife then make a small wedge

Double check that your whipping is secure and batton the wedge into the fork to expand it. Once it is securely fixed, trim the wedge so it fits neatly.

Photo 29-05-2015 09 33 23
Insert to widen and trim

I used my knife to carve some more wood from the inner part of the fork to expand it a bit more. At this stage I was trying the fork out on the upright pole to see how it fitted. Don’t take off too much wood as you need to maintain strength in the fork so it will hold a heavy pot.

Photo 29-05-2015 20 20 47
Use a knife to carve out more wood

Bottom Limb

I split the lower limb nearly all the way down to the main fork. Do this slowly so that the split remains even on either side.

Make sure you get your angles right so that when the crane is placed on the upright everything fits neatly without twisting.

Photo 29-05-2015 09 33 25
Split the lower limb by battoning

I carved another wedge to fit the lower limb split and whipped string on either side. To finish this section off I trimmed the wedge with my saw.

Photo 29-05-2015 09 33 25 (1)
Insert another wedge and whip

Pot Holder Limb

I removed a lot of wood with my axe and knife from the limb that would become the pot holder bar. I also battoned out some little grooves so as to hang pots safely.

Photo 30-05-2015 09 36 40
Carving the pot holder bar

At the end of the bar I also carved out a little recess on which to hang an adjustable pot hook.

After that I added some more binding to the top bar to make it really bomb proof.

That’s it in terms of construction.

Photo 29-05-2015 09 33 26 (1)
Pot holder bar in detail

Aures crane in action

All the hard work is done now so all you have to do is light your fire, insert the upright, attach the crane and pot, adjust the height for optimum cooking and sit back.

The picture at the bottom shows how you can also attach an adjustable pot hook to the end if you want.

Photo 29-05-2015 09 33 27
High, low and balanced

I have attached the Aures crane to the upright for my fixed crane allowing me to hang multiple pots. I have discussed how to make a fixed crane in my previous post How To…. Build a Campfire Cooking Crane.

The adjustable pot hook is only needed if you want different temperatures for the pots hanging off the Aures crane.

Photo 29-05-2015 09 33 27 (1)
Top down with fixed crane above

If you are happy for both pots to be at the same height both can be hung directly off your pot bar if it is long enough.

The crane is easy to adjust for height with the pots attached and you can easily swing it away from the heat when required.

Photo 29-05-2015 09 33 28
Heavy duty

A view from above – one upright – two cranes – three pots

Photo 29-05-2015 09 33 28 (1)
One upright – two cranes – three pots

Do not be put off by the length of the instructions: this crane is very easy to make. Some of my bushcraft friends say that it’s not worth the bother – that may be so for a short term camp but if you want to practice your carving skills it’s perfect for the job.

Photo 29-05-2015 09 33 29
The ultimate aim – to have a brew

I have a feeling I may be writing about a few of the other variations of the Aures crane in the near future.

Cheers and happy carving.

George

7 Replies to “How To…. Carve an Aures Campfire Crane – Single Fork”

    1. Hi alukban

      Glad you liked it. I have a couple of more in this theme to post up but I am very interested in your stand. I will be trying to make one and post it here if that is ok with you?

      Cheers

      George

  1. so i been meaning to schlap together a crane for use since i first saw your tutorials on them. they’re a super neat method by which to dangle your pot/cup over a fire!! i have a dedicated firepit in my yard, and tripods are always so finicky that i often spill my tea/stew juuust as im setting it up. what i made is a lil different than what you’ve shown: i have the boom shear lashed to the Y and split the lashing to allow the Y to engage where the boom is alittle better than level with the ground, then i square lashed a crossbeam to both to keep the angle of the boom/Y set. it does slip when weight is pulled off it, but i’ll be careful. thanks for your very thorough walk-throughs!!

    1. Glad you liked the post. These cranes are great – was using one all last week. The weight is key – kind of makes the friction work. Quite often forget when I take the pot off and the arm slithers down 🙂

Leave a Reply to J. Garcia Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.