How To…. Make Hot Rock Spruce Pitch

After writing the post How To…. Make Spruce Pitch in a Tin Can I promised I would write up one on making pitch using a more primitive method.

Pitch can be made with many different materials and I have covered some of these in that previous post. On this occasion I used spruce resin, beeswax and charcoal dust. Instead of a nice handy tin to prepare it all though I opted to try this out using more primitive materials: hot rocks. I touched on this method previously in the post How To…. Make a Flint-Tipped Arrow but feel it needs its own stand-alone post.

Hot Rock Pitch
Hot Rock Pitch

I collected a lot of resin from some spruce trees in my local area with the use of a stick as I find that this does not damage the trees as a knife would do. Also I look for areas where the resin has pooled at the base of the tree as you can collect all of this without affecting the tree.

Photo 24-04-2014 16 11 37
Spruce Resin

My other ingredients are charcoal dust to give the pitch body (I used the small rock to crush the charcoal) and beeswax to make it flexible. I used the sticks to make the finished pitch stick.

Photo 24-04-2014 14 47 40
Preparation

While I was out collecting resin and preparing everything else I had a rock heating up in the fire. I used a rock that had been heated before so I could be sure it would not crack. (If there is any trapped air or moisture in a rock there is a chance it will crack or, in the worst case scenario, explode.)

To handle the rock I used some wooden tongs I had made up (sorry, no photo).

Photo 24-04-2014 16 31 00
Hot Rock

The rock I had chosen had a slight hollow in the top surface which I thought would help stop the resin from flowing away instantly as it melted. I dragged the rock to the side of the fire, popped a piece of resin onto it and with a small twig moved it around until it had all melted. Some resin did run off but enough was kept in the hollow for me to use.

Photo 24-04-2014 16 38 41
Melting the resin

I then moved the rock onto a piece of curved bark which held some water to act as a coolant as I built up my pitch stick.

Once this was all set up I popped a piece of beeswax into the melted resin and allowed it to mix in (experiment for yourself with ratios).

Photo 24-04-2014 16 39 10
Melting the beeswax

Then I sprinkled a good-sized pinch of charcoal dust into the mixture and carried on mixing it up.

Photo 24-04-2014 16 39 26
Adding the charcoal dust

As the rock was quite small I could only make a little batch of pitch at a time so it did not take long to all melt and mix together.

Photo 24-04-2014 16 44 32
Mix it all up

I used a sliver of wood to scrape the hot, sticky pitch onto a squared-off stick.

Photo 24-04-2014 16 44 56
Scrape onto a twig

The pitch you create using this method is a bit lumpy but still perfectly useable. As soon as I had some pitch on the stick I dipped it into the water to cool it down rapidly. This cooling-down process allowed me to use wet fingers to mould the pitch and smooth it out.

I kept repeating this process until all the melted pitch was on the stick and then mixed up another batch.

Photo 24-04-2014 16 46 14
Cool rapidly in water

The rock was so hot that I was able to keep melting and mixing the ingredients several times to build up the pitch on the stick.

Photo 24-04-2014 16 54 46
Mix more resin, beeswax and charcoal

I found that the curved piece of bark  was very effective for storing water to cool the pitch.

Photo 24-04-2014 16 52 53
Scrape onto the twig and cool again

The pitch stick on the right was made using hot rocks and the one on the left using a tin can. The primitive hot rocks method takes longer and produces a coarser pitch but in my opinion was far more satisfying to make.

Photo 24-04-2014 16 51 09
Keep repeating until you build your own pitch lollipop

The pitch is great for waterproofing things like sinew on arrows. I prepared a ember stick to help melt the pitch so I could cover the sinew you can see in the picture below.

Photo 24-04-2014 16 56 58
Ready to be used

To melt the pitch, simply blow on the ember stick while holding the pitch stick close to it.

Photo 24-04-2014 16 57 24
Heat the resin with an ember stick to melt it

Drip the melted pitch onto what you want to cover and with wet fingers spread it around. Keep re-applying more pitch until you are happy everything that needs to be covered is covered. I sometimes re-heat the area I have covered with the ember stick to further smooth it out.

Photo 24-04-2014 16 57 56
Drip it onto whatever you want to cover, fill or attach

With a little patience this primitive method can produce some very good pitch. I have seen some master primitive technology craftsmen makes some wonderful pieces with the use of pitch.

Photo 24-04-2014 16 10 07
All covered up

I have also made a post showing you how to make pitch in a more modern method using a tin – How To…. Make Spruce Pitch in a Tin Can.

Cheers

George

How To…. Make Spruce Pitch in a Tin Can

I have written various posts now on creating primitive tools and in my article on making arrows I showed you how to make some spruce pitch using hot rocks. This How To…. will lay out all the steps I take to make spruce pitch using tin cans. I find that when I want to make a lot of pitch quickly that this method works well for me however I do appreciate that there are many other methods for making pitch.

The resin produced using this method gives you a much finer pitch than the hot rocks method as you can see in the picture below. The pitch stick on the left was made using the tin method and the smaller rougher pitch stick on the right was made using hot rocks.

I took these pictures while out bushcrafting with my friend Mark Beer in the woods around Silchester in Hampshire (UK)

Photo 08-04-2014 16 50 21
Pitch – Using a tin (left) – Using hot rocks (right)

I tend to use spruce resin when making pitch as this is more readily available where I am and do not tend to use pine resin as this is not so readily available to me. I normally use pitch as a filler material, for example, when fitting a flint axe head into its socket or use it as a covering to waterproof rawhide wraps.

The knife below has had the rawhide wrap covered in the fine pitch from the tin method and is very easy to produce. I am sure that with time I would be able to produce fine pitch using hot rocks but as yet I do not have that skill level.

Photo 24-03-2014 09 55 42
Spruce Pitch – a wonderful material

I collect spruce resin using a flattened stick and a tin (or plastic bag). I use the stick as it does not damage the tree as a knife tip would do. Also it is a messy job to clean the resin of a knife blade and the stick also saves my fingers becoming covered in resin which can be hard to clean off when you do not have access to hot running water.

I collect the resin wherever possible where branches have been broken off and the tree has excreted the resin to protect the damaged area. I do not clean out all the resin but just take a little from many different sites. If you are lucky enough to find a spot where the resin has flowed away from the damaged area and pooled into a big clump then it is fine to collect it all. A good spruce tree will keep excreting the resin so if you are careful you can return at a later date to harvest more.

Photo 07-04-2014 20 52 29
Collecting stick

It did not take long to collect this large tinful of resin as Mark and I managed to find spots where the resin had pooled into large clumps.

Photo 07-04-2014 20 52 42
A good haul

To make pitch I use two baked bean style tins with a small improvised colander in one made out of half a beer can with holes punched through the bottom.

The sticks in the picture below are ready for rolling the pitch on to when it is ready. An alternative is to use a stick like elder with the pith taken out and the pitch poured into the cavity, which makes a kind of pencil.

The charcoal and the beeswax are for binding and tempering the pitch to make it strong but flexible.

Photo 07-04-2014 20 53 17
Equipment

I packed the colander with resin then set light to it. The disadvantage of this method is that you lose a little of the resin but the big plus is that it melts quickly, collects quite cleanly in the bottom of the tin and leaves the detritus in the colander. Two good friends of mine Mark Oriel and Keith Coleman introduced me to this method: previously I’d just put the resin into a tin, placed it into some embers and scooped out the detritus when it had melted.

Photo 07-04-2014 20 59 57
Packing and firing

As the resin burns and melts in the tin I then take the time to crush the charcoal down to fine dust with a small stone. This fine dust acts as a binding agent that the resin can cling to and make the pitch you produce stronger. There are many other materials that you can experiment with as binding material such as ash and rabbit droppings. The Primitive Ways website has an excellent article on making pine pitch using a tin but in a different way and discusses other binding agents.

Photo 07-04-2014 22 16 14
Making charcoal powder

Soon all the resin had melted and dripped down into the tin (it looks black from previous pitch making). As the detritus is left in the colander the resin in the tin is very fine, which makes for very smooth pitch.

Photo 07-04-2014 22 19 18
Liquid resin and remnants

I tend to put in as much charcoal dust as there is spruce resin and mix it all together while the resin is still hot.

Photo 07-04-2014 22 22 11
Add some charcoal

I then added some lumps of beeswax. I have heard some folk say that they put in the same quantities for everything but I usually just put in a small block or two of beeswax. I also use beeswax balsam as this is easy to buy in shops and it seems to work just as well as pure beeswax. Experiment for yourself with quantities to see what works for you.

Photo 07-04-2014 22 22 29
Then some beeswax

I then put the tin into the embers of my fire and mix it all up. Watch out that you don’t overheat it as it will froth up and spill over. I normally have some tongs nearby so that I can move the tin around the embers so as to better control the heat.

Photo 07-04-2014 22 23 44
Melt and mix

I use the tongs to move the tin out of the embers when all the beeswax has melted and been thoroughly mixed in. The tin will be scorching hot and the liquid pitch will scald you badly if it comes into contact with your skin.

Photo 07-04-2014 22 24 47
Remove from heat carefully

I let the pitch cool slightly and so it becomes a little bit  tacky. While it is cooling down I make sure I have a little pot of water ready.

I then put one of the sticks into the mixture and roll it a few times (I try to square off the stick as this helps catching the tacky pitch) until I have some pitch on the stick. I then dunk the stick into the water to rapidly cool the pitch down. The pitch will not dissolve in the water due to the oils, charcoal and beeswax in it and but will bind to the stick.

Photo 07-04-2014 22 30 04
Roll and dip

I then repeat the process again and again to build up more layers of pitch on the stick. You will find loose bits of pitch will float in the water so just fish them out and pop them back into the tin and they will melt back into the mixture.

Photo 07-04-2014 23 16 54
Roll, dip and wet your fingers

After two or three times doing this you will need to use your fingers to mold the pitch into a tight blob on the end of the stick and also to smooth it out. As the pitch can still be quite warm and sticky you need to keep your fingers wet during this process. If your fingers are dry then the pitch will just stick to them.

Photo 07-04-2014 23 17 26
Smooth the hot pitch down

In no time at all you will have a good amount of spruce pitch to help you with making primitive craft items.

Photo 07-04-2014 22 33 37
Pitch Sticks

To use a pitch stick I just heat the end of it with a glowing ember until it starts to melt and then drip the liquid pitch onto whatever I am making.

Photo 09-03-2014 14 14 30
To use just heat

I have used pitch for waterproofing bindings on arrows.

Photo 09-03-2014 14 15 28
Great for arrows

It is also great as a filler as in this small hatchet. I filled the socket with pitch, inserted the flint axe head and then bound it all up with rawhide.

Photo 26-03-2014 16 13 56
And great for axes

I have also published an article on making pitch in a primitive fashion using hot rocks instead of a tin – How To…. Make Hot Rock Spruce Pitch.

Cheers

George