How To…. Carve and Use an Adjustable Pot Hanger

The main benefit is – is that the tea gets made

I was trimming an ash tree in my garden recently with my friend Paul and I managed to save a few pieces for Atlatls and pot hangers.

I have previously shown you how to carve a collapsible pot hanger so that it can fit into a pot when not in use but on a lot of occasions I just whittle one when I need one.

The type of pot hanger I am talking about is shown below hanging off a ‘Wagon/Waugan Stick’ (pronounced waygone or worgan – I hear different variations on this from different people) campfire  set up. The pot hook is adjustable in that the pot is easily raised or lowered by using the different hooks on the pot hanger.

Photo 22-05-2014 00 36 16
A simple pot hook

I started off with a piece of ash that had a fork in it at a good angle (to form a hook) and finished up with something that allowed me to be able to quickly or slowly cook/boil something.

On the right you can see the finished pot hanger in action. To help stop any confusion I will refer to the large hook holding the small kettle as the ‘pot hook’ and the small hooks as the ‘adjusting hooks’.

Photo 22-05-2014 00 26 15
Before and After

To begin with I trimmed off all the knobbly pieces using powerful chest lever and locked arm cuts. See my How To…. on knife Safety for more information on these types of cuts.

Photo 15-05-2014 15 30 23
Powerful cuts

I then trimmed the bark off using a powerful shoulder cut. I had the work piece placed on the ground here off to one side so as to brace it and to work safely.

Photo 15-05-2014 15 31 31
Braced

To strip the bark around the hook area I used a gentle chest lever grip.

Photo 15-05-2014 15 35 09
Fine cuts

The bottom of the pot hanger was more difficult to trim as I had not left any excess wood to hold on to. The main thing I needed to consider here was keeping my eye on where my thumb was  on the hand holding the pot hanger.

Photo 15-05-2014 15 36 33
Work safely near the ends

As I needed to use the point area of the blade to trim around the hook I kept the pot hook resting on a small log so that if the knife slipped it would hit the ground. My friend Charlie showed me how to use the knife and the curve of the pot hook to create a fulcrum, making the stripping of the bark safer. I tried to photograph this but they did not turn out well.

Photo 15-05-2014 15 39 40
De-barking the hook area

I also rounded the bottom of the pot hanger and then used the back of my knife to strip off the remnants of the inner bark.

Photo 15-05-2014 15 47 07
De-barking with the back of the knife

To make the adjusting hooks I used a batton (a large stick) to carve a cross into the wood – an X cut. I placed my X cuts in line with the pot hook as much as possible. After a couple of good smacks with the batton the knife had cut well into the wood.

Photo 15-05-2014 15 48 08
Batton in the first X cut

I then repeated the process for the other part of the X cut.

Photo 15-05-2014 15 49 57
Then the second X cut

A simple X cut – this cut makes the carving of the adjusting hook much easier.

Photo 21-05-2014 15 37 08
The X cut

So that the pot hanger can hang properly you must remove the wood at the bottom of the X cut first (the bottom being the quarter of the X cut closest to the pot hook).

I use very fine cuts here and the original X cut acts as a stopper point so that you only cut away the wood that you need to.

Photo 21-05-2014 15 38 45
Fine cuts

I normally remove a small area of wood just below the point of what will become the adjustable hook.

Photo 21-05-2014 15 42 08
Remove the bottom of the X first (nearest the hook)

Once I’d removed the wood from the lower quarter I then removed the wood from one of the side quarters.

Photo 21-05-2014 15 45 36
Remove the sides of the X

Then I removed the wood from the other side quarter leaving only the top quarter to act as the adjustable hook.

Photo 21-05-2014 15 47 12
Deepen the sides of the X

I kept carving down until I had exposed enough of the wood that I could carve out the final part of the adjustable hook.

Photo 21-05-2014 15 48 47
Ready for the undercut

The final part I needed to do was to make an undercut below the point of the upper quarter. I kept reducing the wood until a nice point appeared.

Photo 21-05-2014 15 51 16
Fine cuts again on the point

You can really see that undercut appearing in the picture below now. For safety I kept the pot hanger braced on the ground (a stump works as well) while I was carving it out.

For this pot hook I carved a further 2 hanging hooks along its length.

Photo 15-05-2014 15 51 59
Carve deep but safely

This is the final rough shape you are looking for. Any further carving or sanding would be purely for decoration only.

Photo 22-05-2014 09 42 42
A good point

This pot hanger is particularly suited to the Wagon set up – Wagon (‘way gone’) coming as far as I know from the old tale that if you leave this set up standing when you leave your camp, it points the way for the naughty wood spirits to follow you 🙂

Photo 22-05-2014 00 49 44
Side view of the Way Gone  set up

The hanging hooks attach to the Wagon stick by sitting in a small dimple on the end of it. In this set up I also used a forked stick to give the Wagon height and a smaller (Dead Man’s Finger) stick at the bottom of it to counterbalance everything.

Photo 22-05-2014 00 21 59
In detail

The whole set up is very easy to adjust for a fast or slow boil/cook.

Photo 22-05-2014 00 19 01
Adjustable height

This is a great project for any bushcrafter to keep their hand in with simple carving techniques. It looks very simple at first but there are some tricky cuts that if you are not careful can cause a nick or two but the main benefit is – that the tea gets made.

Photo 17-05-2014 17 49 15
Brew time

Cheers

George