How To…. Make a Flint-Tipped Arrow

I put this How To…. together to show how to construct a couple of primitive arrows. I used mainly primitive tools with the exception of a few modern touches: the occasional use of a steel knife, adding false sinew when I ran out of real sinew, some sandpaper, a copper-tipped flaker and bleached feathers.

Preparing the arrow shafts

I made these arrows while on the Woodcraft School Primitive Technology course in 2009. John Rhyder the course instructor supplied us with pre-cut branches from a spindle (Euonynus europaeus) tree, which has traditionally been used for the manufacture of arrows as it is a hard wood and takes a point well. Another option that was available to us was hazel (Corylus avillana) as there was some on site. I chose to use spindle as I had never used it before to make arrows.

Photo 10-03-2014 09 47 41
Flint-tipped arrows

I used the back of my knife to scrape the bark off the wood but this would traditionally have been done with a piece of sharp flint or other such stone. For safety I kept the knife still and pulled the green stick backwards, scraping bark off with the back of the blade. I like this method as the blade stays still making it very safe. I then roughly sanded each of the branches with sandpaper. This could have been completed traditionally with either a handful of sand or a soft rock such as sandstone.

Photo 09-03-2014 14 21 55
De-barking

I then heated the branches over an open fire. I was careful not to scorch the wood as this changes its properties and makes it brittle. The trick is to slowly turn the branch in a circular fashion, heating evenly all around the section of wood that needs straightened. This in effect creates steam in the wood as the sap heats up and so allows you to slowly straighten the arrow (this method works best on green wood). To straighten the bumps in the wood you need to hold it in position (as straight as possible) until it cools and sets into its new shape.

Photo 09-03-2014 14 23 38
Heating and straightening

Making a Self Nock

Next I needed to make the nock for the string. I cut two small grooves (opposite each other) at the thin end of each shaft. Then about a centimeter down the shaft (showed here in red) I rolled the knife edge to mark a thin line at 90 degrees to the first grooves (too fine to see in the picture).

I then placed the edge of the knife into one of the larger grooves to split the wood down to the lower line. The small cut in the wood at the lower line helps stop the split running off too far. I then repeated the procedure on the opposite groove.

I wiggled the centre section back and forth until it started to break away from the main arrow shaft. In the bottom picture you can see the nock starting to appear.

photo
Self Nocks

The resulting peg finally pops out after a lot of wiggling about. Freejutube has an excellent video on making a primitive nock using a slightly different method – Arrow snap self-nock – with flint and bone tools

Photo 09-03-2014 14 26 04
The knocks

Preparing the Flights

John Ryder provided feathers for us to use. Due to health and safety requirements John had to supply his students with feathers that had been washed: traditionally of course the remnants of bird kills would have been kept and the feathers used for this job. If the feathers are from the same wing they make excellent flights, making your arrows more accurate.

Photo 09-03-2014 16 15 39
The Flights to be

I used my knife tip to start the split of the feathers to create the flights – a sharp piece of flint would have worked just as well. After the initial split had been made I used my fingers to split the rest of the feather. I tried to be very careful here to keep the split in the centre of the spine of the feather all the way to the end. It gets a bit tricky as it tapers out near the end.

I split and trimmed the feathers leaving enough of the spine at each end for wrapping purposes.

Photo 09-03-2014 16 17 03
Splitting out the flights

Making Sinew Cordage

To wrap the feathers onto the shaft I used deer sinew. This needs to be pounded gently between two stones until all the sinew fibres separate.

Photo 09-03-2014 16 17 48
Sinew

This takes time but it is worth it to see all the strands of sinew start to appear.

Photo 09-03-2014 16 18 29
Breaking down the sinew

Here you can see the fibres starting to really fall apart. There wasn’t enough real sinew for everyone so I had to supplement it with some false sinew: dental floss is another possible alternative.

I rolled the sinew strands to make them stronger and wet each strand with saliva. This allows the sinew to bind to the shaft as the fats in it act like a glue when wet. On the right you can see some sinew that is ready to use as wrapping.

Photo 09-03-2014 16 21 07
Finished sinew

Attaching the Flights

To aid in the process of attaching the flights to the shaft I tried out another type of glue made by crushing bluebell leaves to a pulp between my fingers. The resulting gloop was supposed to act as a first fixing to help keep the flights in place before wrapping; it turned out to be a little bit tacky but nowhere near strong enough to act as a glue. In the bottom picture you can just make out the shaded area on the shaft where the bluebell ‘glue’ was placed.

Photo 10-03-2014 08 52 35
Bluebell glue

In the end I just used sinew to hold the flights in place. You can see the bluebell stain on the shaft in this picture.

Photo 10-03-2014 08 54 18
First tie off

I then wrapped the flights at the top with sinew (bottom left) and then to finish this stage I wrapped the body of the flights with more sinew (bottom right).

I also wrapped sinew just below the nocks on each arrow to strengthen them. You can see this clearly in the arrow on the right. If I hadn’t reinforced the nocks with sinew they could easily have split with the forces of the bow string as soon as I shot them.

Photo 10-03-2014 08 54 54
Tied off with sinew

Creating and Using Pitch

Once the sinew was attached to each arrow I decided to put together some pine pitch. This was to cover the sinew to protect it from fraying and also to waterproof it. The name pine pitch is a bit misleading as I used spruce resin, since that was what was readily available in the area. After collecting the resin that had oozed from spruce trees (the tree uses the resin to seal any damaged areas on its bark) I mixed  it with fine charcoal (to give it strength) and beeswax (to give it flexibility).

I used the small rock (left hand picture) to grind the charcoal and a large flat rock (top right) as a preparation table. I heated the square rock in the fire to help with melting and mixing everything together.  The sticks were used as mixers and to store the resin (see below). The hot rock I used had been heated before many times so there was no risk of it exploding (which can happen if they contain trapped air).

On the heated rock (bottom right) I heated the first lump of resin, and as it melted I scraped off any debris such as bark.

Photo 10-03-2014 08 59 55
Pine Pitch Prep

I kept adding more and more resin, charcoal and beeswax (I just added charcoal until the mixture thickened slightly and added beeswax in little lumps) until it had all melted. The rock was super-heated so I had to take great care not to burn myself.

Photo 10-03-2014 09 08 11
Mixing

The rock had a slight indentation to collect the melted resin. It doesn’t look like there is much resin here but it was enough for what I had to do.

Photo 10-03-2014 09 09 19
Hot Pine Pitch

Using two sticks, one to scrape the pine pitch up and one to hold the cooling pitch, I coated the holding stick with the pitch mixture then submerged it in a pot of cold water to harden it. I would then repeat the process adding more and more layers. Using cold water speeded up the whole process.

Here you can see the pine pitch building up on the stick. This primitive method does not give you very fine pitch as you would get using a modern method but it does work surprisingly well

Photo 10-03-2014 09 10 09
Creating a Pine Pitch Stick

I made up two pine pitch sticks in the end. The stick on the far left has been charred and can be re-ignited quickly by dipping it into a fire to create heat to melt the pine pitch again to coat the sinew on the arrows. This protects the sinew and gives the arrow a nice finish

Photo 10-03-2014 09 10 39
Prepping to coat the sinew

After re-lighting the charred stick I used it to to re-melt the tip of a pitch stick (top picture). I found it fairly easy to drip the melting  pitch onto the area of sinew on the arrow I wanted to cover (bottom picture).

Photo 10-03-2014 09 11 33
Heat and coat

As I dripped the pine pitch onto the sinew I wet my fingers so that I could smooth the resin out and spread around evenly (John the course instructor is in the left hand picture demonstrating this). If you do not wet your fingers the hot pitch could burn you and also it will stick to your fingers (out in the woods without hot running water this is a pain to clean up).

Photo 10-03-2014 09 14 05
Re-heat and smooth out

Knapping the Arrow Tips

The next stage in the process was to make some arrow tips. I had collected up some shards of flint left over from the course we had with John Lord. Thankfully there was a mass of leftover flint for me to look through and choose from. All of the pieces shown below I thought could be made into decent arrow tips or barbs with the minimum of effort.

Photo 10-03-2014 09 16 00
Possible points

The next stage was to pressure flake the pieces with a copper tipped pressure flaker and an antler tine (I wanted to try both tools) into usable arrow heads. The glasses were worn to protect my eyes from flying pieces of flint and the glove protected me against cuts. I placed under the flint a strip of leather to give support and further protect my hand.

The picture on the right did not turn out very clear (a smear on the lens of my camera) but I soon had  an arrowhead ready to insert into my arrow shaft. Using the same method as I used to make the knock, I created a groove at the arrow tip.

Photo 10-03-2014 09 23 34
A bit of knapping

I re-worked the other pieces and after a little touching up these other flint points were ready to be used.

Photo 10-03-2014 09 26 42
The rest of the finished points

Attaching the Tips 

I then coated the arrowhead with some pine pitch and placed it into the groove on the shaft. I then coated the tip of the shaft in more pitch and wrapped sinew round it to keep the arrowhead secure.

Update 13/03/2014 – I have been advised by one of the Primitive Arts Society members David Colter that  it is very important to securely bind the shaft immediately below the point for a length of about a centimetre to prevent it from splitting on impact and failing to drive the point into the target. There is a very good experiment showing this in the Traditional Bowyers Bible Vol 3. I did not bind it for a full centimeter in my example (thanks for the update David).

Photo 10-03-2014 09 24 33
Attaching points

I finally added more pitch to cover the sinew to waterproof it all.

Photo 10-03-2014 14 31 40
Well attached

Based on archaeological evidence I decided to add a barb to the arrow. I firstly scraped a groove along the arrow shaft then put some pine pitch into it.

I then placed a long thin piece of sharp flint onto this pitch and coated more around the base of it (bottom picture) The barb is designed to cause maximum damage to the prey animal as the arrow enters its body.

Photo 10-03-2014 14 32 40
Attaching a barb

I finished two arrows in this project. The one I completed for this tutorial is the one on the right.

Photo 10-03-2014 09 47 41
Finished arrows

Using similar techniques I was able to produce an Atl atl set as well.

Photo 10-03-2014 14 35 52
Atlatl extras

I have never shot these arrows at a modern target as I don’t want to break off the tips but I did shoot them into some bales of loose hay and was very impressed with their accuracy.

This was a great project as it introduced me to some primitive but very effective techniques in arrow making.

Cheers

George

 

 

5 Replies to “How To…. Make a Flint-Tipped Arrow”

  1. Anothe great how to George. I like how you attached the flights, I did some a while back and they didn’t come out quite so well… But I will have to give it another go.

  2. Remember doing this and then shooting them, points shattered on 1st impact, came to the conclusion that the arrow points found in grave deposits (Amesbury archer, Boscombe bowman) were to my mind offerings too good for every day hunting as rough but sharp points will do the job and take a lot less time to make.
    Nice editorial George.

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.